Protect against UV, fading, yellowing and wear with our sealers.
Durathane is a two-component aliphatic polyurethane that exhibits excellent abrasion and chemical resistance as well as UV stability. Applied thin in one or more coats over any Shield epoxy system, Durathane is an excellent topcoat and is suitable for both residential and commercial applications, including garages, warehouses, vehicle service centers, food preparation areas and airport hangars.
SlipGrip™ is a micronized powder designed to provide slip resistant properties to solvent-based acrylic sealers, specifically SuperSeal™ 2000, 400, 350, 100, GemKote™ 400, 350, and 100 and PS-18™ 600, 400 and 100.
Add 1 lb. container to a five-gallon bucket of sealer of your choosing or measure and weigh off 3 oz. per gallon for added traction on any floor. SlipGrip is often applied to an initial sealer coat. However, if additional traction is desired, SlipGrip may be added to additional coats. Remember to mix sealer frequently during application to maintain a consistent coating with the additive.
Refer to the TDS for complete mixing and application instructions.
Concrete Coatings, Inc. SuperSeal™ 20WB is a water-based acrylic sealer for general everyday use. This product may be used when a solvent-based sealer cannot due to safety or flammability concerns. It may be applied to almost any surface: concrete, tile, cementitious overlays and much more.
Concrete Coatings, Inc. Dri-Look™ Masonry Sealer is designed specifically for brick and manufactured stone surfaces to provide an invisible barrier against water and the elements, yet leave the natural look of these surfaces with no visible sheen. Micronized polymers provide all the necessary protection to extend the life of these surfaces.
SuperSeal™ 2000 600 VOC-Acrylic Sealer (VOC requirements vary by region)
Concrete Coatings, Inc. SuperSeal™ 2000 is an aromatic acrylic sealer that can be applied to almost any surface: concrete, tile, cementitious overlays and much more. Use SuperSeal™ 2000 for a gloss or matte finish as well as for its UV and stain protection.
For application tips visit the Frequently Asked Questions page or Contact Us.
Please check local regulations for VOC requirements.
Concrete Coatings, Inc. GemKote™ uses the same resin as SuperSeal™ 2000 with a VOC content less than 400 g/l, 350 g/l or 100 g/l for local regulations requiring a lower VOC. GemKote™ is an aromatic acrylic sealer that can be applied to almost any surface: concrete, tile, cementitious overlays, natural stone and much more. Use GemKote™ for a gloss finish as well as for its UV and stain protection.
Concrete Coatings, Inc. SuperGlaze™ WBU can be used as a single-component water-based urethane for greater durability on non-vehicular applications. This sealer has low VOC content and quick drying properties with low odor. SuperGlaze™ WBU requires a primer prior to application. SuperSeal™ 20WB, Shield 50™ or UV Shield™ may be used as a primer.
Please check local regulations for VOC requirements.
• Excellent Working Time
• Excellent Moisture Resistance
• Single Component
• Quick Drying
A penetrating, natural-look sealer with no sheen. Particularly effective on tile, natural stone and grout.
Unsealed and unprotected tile and grout can stain, chip, crack or fade. Apply CCI Tile Armor™ WB to your tile, natural stone and grout to protect against staining and damage or as a pre-grouting sealer.
CCI Tile Armor™ WB can be used on grout, limestone, saltillo tile, clay tile, stucco and concrete/masonry. Effective on interior and exterior applications.
Please check local regulations for VOC requirements.
Add a wet-look finish to your tile, grout or natural stone without adding sheen.
Unsealed and unprotected tile and grout can stain, chip, crack or fade. Apply CCI Tile Armor™ Enhancer to your tile, natural stone and grout to protect against staining and damage or as a pre-grouting sealer.
In addition to protecting your tile, grout and natural stone, CCI Tile Armor™ Enhancer will give your surface a "wet-look" without adding sheen.
It can be used on grout, limestone, saltillo tile, clay tile, stucco and concrete/masonry. Effective on interior and exterior applications.
Please check local regulations for VOC requirements.
Concrete Coatings, Inc. UV Shield™ is a 100% solids and 100% cross-linked product that can be applied to almost any surface: wood, tile, stone etc. It is used mainly as a clear coat over full or partial flake or quartz systems. UV Shield™ is also easily pigmented for use as a colored topcoat that will not show the effects of UV exposure that is common to epoxies. Shield 50™ may be used as a primer prior to UV Shield™ application.
We are always innovating.
Want to keep up with the latest? Sign up for our updates!
